Celtifier      GSM based controller

     Monitor and control anything via GSM - your cellphone

- Functionality can be redesigned by request, e.g. pulse counts, GPRS etc

• Sends an SMS or miss-call when a sensor or any input condition is activated

• switches anything on or off by sending it an SMS or miss-call

• monitors and reports anything connected to it

• communicates with any cell phone anywhere

• responds only to preset phone numbers

• phone numbers and other setups can be done via SMS's

• Input- and output modules can be supplied for:
  - optically isolated inputs
  - relay outputs
  - RS232/RS485 serial communication
  - GPS

• Functionality can be redesigned by request,
  e.g. pulse counts, GPRS
  

• The electronics can be packaged into various enclosures:

The Celtifier inexpensively provides you with a unique remote control and information mechanism
fully under your control.
Stay in touch with your home, office, car, business or production plant.

By using the SMS facility of your personal cellular mobile phone you can send instructions to and be notified by the Celtifier installation.

Sending commands to your home or business

Sending an SMS from your mobile phone will cause the Celtifier to turn on the lights in your home, start the water pump for the irrigation system, start the coffee machine and turn on the heating system.

Through an inexpensive relay module (about R150) it can provide eight 10 amp relay outputs which can be connected to eight different appliances.

With an inexpensive expansion board the number of outputs can be increased to any number on request.

Receiving vital information

Connected to your burglar alarm system for example, the Celtifier can send you a message when the alarm has activated and which zone was involved if the zones are individually connected. There are eight signal connections which can provide information on eight sensors.

With an inexpensive expansion board the number of inputs can be increased to any number on request.

You can interrogate the Celtifier to receive information about which outputs are on or off, which inputs or sensors are activated, what happened the last time it sent an SMS or get the remaining air time.

Once a month you will be notified automatically of the remaining air time.

Stay in control - be empowered

You can enter telephone numbers into the Celtifier to which it may respond or send SMS's.
So no one else can tamper with your Celtifier installation.
For each output you can set whether it should turn on or off according to your SMS or whether it should give a pulse.
The outputs can also be set to activate when you send it a miss-call with a certain number of rings.
For each input you can tell it to send you an SMS or send a miss-call with a certain number of rings.
You can also enter the messages to be sent for each input activation and to which number it is to be sent.
All by sending an SMS.

The Celtifier can be installed by any DIY enthusiast or by any security installation professional.

SPECIFICATIONS

Controller board

Power supply	9 - 18V dc
Dimensions	84 x 84 x 15mm
Outputs	7 x relay drivers for 12V relays (up to 48V, 350mA )
	1 x 5V reference for external devices
Inputs: discrete	7 x DC/AC 5V - 18V (voltage can be extended with external resistor)
Inputs: analog	4 x 0 - 5V or 0 - 20mA
Power consumption	approx. 50mA
Operating temperature	-5 to 55DegC

The SIM card PIN number has to be set up by the supplier.
Alternatively a PC interface can be supplied to communicate with the Celtifier
by which the SIM card PIN code can also be set.

Input and power Module CIP6

Inputs	6 x DC/AC 5V - 18V optoisolated (voltage can be extended with external resistor)
	1 x "auxiliary power present" signal (internal)
	signal for low-battery montoring
backup	connection for 12V lead acid battery
Auxiliary supply	110V ac or 220V ac

Output Module COP7

Outputs	7 x SPDT relay contacts 250Vac 10A
Dimensions	fits on top of controller board, increases the total height to 46mm